USED HAAS TM2 – 2008

The HAAS TM2 – 2008 is a CNC toolroom vertical machining center designed for shops that need the flexibility of a toolroom mill combined with the accuracy and control of a Haas CNC system. Unlike the TM2P, the TM2 is the non-ATC version, making it a simpler and generally more economical choice for prototype work, maintenance machining, tooling, education, and low-volume production.

The TM2 provides 40 inches of X-axis travel, 16 inches of Y-axis travel, and 16 inches of Z-axis travel, giving it a large working envelope for a toolroom-class machine. Its 40-taper spindle is rated at 7.5 HP with a 4,000 RPM maximum speed, and the machine uses a direct-speed belt-drive system. Haas specifies a 57.8 x 10.5-inch table, three T-slots, and a maximum evenly distributed table load of 350 pounds.

Because the TM2 does not have the automatic tool changer found on the TM2P, it is particularly attractive for operations where manual tool changes are acceptable and simplicity is more important than automated production. The machine supports Haas conversational programming, making it accessible for operators who may not have extensive G-code experience.

---

HAAS TM2 – 2008 – AXIS

Specification	Details
Machine Type	CNC Toolroom Vertical Machining Center
Axis Configuration	3-Axis
X-Axis Travel	40″ / 1,016 mm
Y-Axis Travel	16″ / 406 mm
Z-Axis Travel	16″ / 406 mm
CNC Interpolation	3-Axis
4th-Axis Capability	Available / Optional
Rotary Integration	Available
Spindle Orientation	Available
Rigid Tapping	Available

---

HAAS TM2 – 2008 – AXIS TRAVELS / WORK ENVELOPE

Specification	Details
X-Axis Travel	40″ / 1,016 mm
Y-Axis Travel	16″ / 406 mm
Z-Axis Travel	16″ / 406 mm
Spindle Nose to Table Maximum	Approx. 20″ / 508 mm
Spindle Nose to Table Minimum	Approx. 4″ / 102 mm
Work Envelope	40″ x 16″ x 16″
Table Length	57.8″ / 1,467 mm
Table Width	10.5″ / 267 mm
Maximum Table Load	350 lbs / 159 kg

The 40-inch X-axis travel is a major advantage of the TM2, allowing it to accommodate long workpieces, plates, fixtures, and tooling components while retaining a relatively compact toolroom configuration.

---

HAAS TM2 – 2008 – CAPACITY / TABLE

Specification	Details
Table Length	57.8″ / 1,467 mm
Table Width	10.5″ / 267 mm
T-Slot Width	0.626–0.630″ / 15.9–16.0 mm
T-Slot Center Distance	4″ / 102 mm
Number of Standard T-Slots	3
Maximum Table Load	350 lbs / 159 kg
Workholding	Vise / Fixture / Rotary
4th-Axis Integration	Available
Table Type	Fixed T-Slot

The long table provides useful support for long components and multiple workholding setups. The specified 350-pound maximum evenly distributed load should be considered when planning heavier fixtures or workpieces.

---

HAAS TM2 – 2008 – SPINDLE

Specification	Details
Spindle Type	Direct-Speed Belt Drive
Spindle Taper	CT40 / BT40
Maximum Spindle Speed	4,000 RPM
Spindle Motor	7.5 HP / 5.6 kW
Maximum Torque	33 ft-lb @ 1,200 RPM
Drive System	Belt Drive
Bearing Lubrication	Grease Packed
Spindle Cooling	Air Cooled
Spindle Orientation	Available
Tool Retention	Manual Tool Change

The TM2 uses a 7.5 HP, 4,000 RPM, 40-taper spindle, providing a practical combination of torque and versatility for general machining applications. The 4,000 RPM spindle differentiates the TM2 from the faster TM2P configuration.

---

HAAS TM2 – 2008 – TOOLING

Specification	Details
Tool Changer	None
Tool Change	Manual
Tool Taper	CT40 / BT40
Spindle Taper	40 Taper
Tool Retention	Manual
Tool Capacity	Operator Dependent
Tool Management	CNC Offset Management
Automatic Tool Change	No
Toolholding	CAT40 / BT40 Compatible
Production Style	Manual Tool Change

Unlike the TM2P, the TM2 does not include an automatic tool changer. This makes the machine mechanically simpler and can be advantageous for prototype, repair, maintenance, and low-volume work where tool changes are relatively infrequent.

---

HAAS TM2 – 2008 – CONTROL SYSTEM

Specification	Details
CNC Control	Haas CNC Control
Programming	G-Code / Conversational
Conversational Programming	Yes
Intuitive Programming	Available
Rigid Tapping	Available
Work Offset Management	Yes
Tool Offset Management	Yes
User-Definable Macros	Configuration Dependent
Ethernet	Configuration Dependent
USB	Configuration Dependent

The Haas CNC control allows operators to program the TM2 using conventional G-code as well as conversational programming functions. The platform was intended to be relatively easy to learn for operators transitioning from manual machining to CNC.

---

HAAS TM2 – 2008 – FEEDRATES

Specification	Details
X-Axis Rapid Traverse	Approx. 200 IPM
Y-Axis Rapid Traverse	Approx. 200 IPM
Z-Axis Rapid Traverse	Approx. 200 IPM
Maximum Cutting Feedrate	Approx. 200 IPM
X-Axis Maximum Thrust	2,000 lbf
Y-Axis Maximum Thrust	2,000 lbf
Z-Axis Maximum Thrust	2,000 lbf
Feedrate Override	Standard
Linear Interpolation	Yes
Circular Interpolation	Yes

The TM2’s rapid and maximum cutting feedrates are approximately 200 IPM, providing adequate performance for general toolroom and prototype machining.

---

HAAS TM2 – 2008 – COOLANT & CHIP MANAGEMENT

Specification	Details
Flood Coolant	Available
Coolant Pump	Available
Coolant Tank	Configuration Dependent
Programmable Coolant	Available
Chip Auger	Optional / Configuration Dependent
Chip Conveyor	Configuration Dependent
Air Blast	Available
Through-Spindle Coolant	Optional
Coolant Filtration	Configuration Dependent
Mist Collector	Optional

Coolant and chip-management equipment can vary on individual used TM2 machines. Buyers should inspect the coolant pump, tank, lines, nozzles, chip removal arrangement, and any optional equipment before purchasing.

---

HAAS TM2 – 2008 – AUTOMATION / PROBING

Specification	Details
Automatic Tool Changer	No
Wireless Intuitive Probing	Optional / Configuration Dependent
Work Probe	Optional
Tool Probe	Optional
4th-Axis Drive	Available
4th-Axis Wiring	Available
Rigid Tapping	Available
Conversational Programming	Yes
Rotary Table Integration	Available
Manual Tool Change	Standard

The TM2 can be equipped with additional probing and rotary capabilities, but its defining characteristic is the absence of an automatic tool changer. This makes it more straightforward than the TM2P and potentially easier to maintain.

---

HAAS TM2 – 2008 – POWER REQUIREMENTS

Specification	Details
Spindle Motor	7.5 HP / 5.6 kW
Single-Phase Input	220 VAC
Single-Phase Full Load	Approx. 40 A
Three-Phase Low Voltage	220 VAC
Three-Phase Low Voltage Full Load	Approx. 25 A
Three-Phase High Voltage	440 VAC
Three-Phase High Voltage Full Load	Approx. 13 A
Electrical Service	Single- or Three-Phase
Shop Air	Required
Air Requirement	4 SCFM @ 100 PSI

The TM2 platform can operate on single- or three-phase power depending on configuration. Haas specifies approximately 4 SCFM at 100 PSI of compressed air.

---

HAAS TM2 – 2008 – DIMENSIONS

Specification	Details
Approximate Shipping Length	127″
Approximate Shipping Width	78″
Approximate Shipping Height	100″
Approximate Shipping Weight	5,060 lbs
Metric Weight	Approx. 2,295 kg
Floor Space	Compact Toolroom Configuration
Installation	Industrial
Rigging	Required

Published TM2 dimensions list approximately 127 x 78 x 100 inches and approximately 5,060 pounds shipping weight for the standard configuration. Actual installed dimensions can vary with enclosure and optional equipment.

---

HAAS TM2 – 2008 – GENERAL INFORMATION

Specification	Details
Manufacturer	Haas
Model	TM2
Year	2008
Machine Category	Vertical Machining Center
Machine Type	CNC Toolroom Mill
Axis Configuration	3-Axis
X-Axis Travel	40″
Y-Axis Travel	16″
Z-Axis Travel	16″
Table Size	57.8″ x 10.5″
Maximum Table Load	350 lbs
Spindle Speed	4,000 RPM
Spindle Power	7.5 HP
Spindle Taper	CT40 / BT40
Tool Changer	None
Tool Change	Manual
Maximum Feedrate	200 IPM
CNC Control	Haas CNC
4th-Axis Ready	Available
Shipping Weight	Approx. 5,060 lbs

---

INDUSTRIES THAT USE HAAS TM2

The HAAS TM2 is suitable for:

• General machine shops
• Tool and die
• Mold manufacturing
• Aerospace
• Automotive
• Defense
• Maintenance and repair
• Prototype manufacturing
• Educational facilities
• Industrial machinery
• Contract machining
• Precision engineering
• Fabrication

It is especially useful for businesses that need a large X-axis travel but do not require automatic tool changing.

---

TYPICAL PARTS HAAS TM2 CAN PRODUCE

The TM2 can produce:

• Brackets
• Mounting plates
• Fixtures
• Jigs
• Housings
• Flanges
• Tooling components
• Prototype parts
• Machine components
• Repair components
• Industrial brackets
• Automotive components
• Custom production parts

Typical operations include face milling, pocketing, contouring, drilling, tapping, boring, reaming, slotting, and 3-axis profiling.

---

WHY CHOOSE HAAS TM2

The main advantage of the HAAS TM2 is its combination of 40 x 16 x 16-inch travels with a straightforward toolroom-mill configuration. The 40-inch X-axis travel gives it substantially more capacity for long components than smaller TM-series machines.

Its 7.5 HP, 4,000 RPM, 40-taper spindle is appropriate for general machining applications, while the manual tool-changing arrangement keeps the machine simpler than the TM2P.

For prototype shops and maintenance departments, the lack of an automatic tool changer is not necessarily a disadvantage. Operators can manually select tooling according to the job, while the Haas CNC system provides accurate positioning and repeatable machining.

---

WHY BUY USED HAAS TM2 – 2008

A used 2008 HAAS TM2 can be an economical CNC solution for shops that need a large work envelope without paying for features they may not require.

The machine’s 40-inch X-axis travel, 40-taper spindle, 7.5 HP motor, and Haas CNC control make it capable of handling a wide range of machining tasks. Its simpler architecture compared with an automatic-tool-changing TM2P can also make it attractive for maintenance and prototype environments.

Before purchasing, inspect the spindle, ballscrews, linear guides, table, way covers, drawbar, control electronics, coolant system, lubrication system, and electrical cabinet.

For a 2008 machine, buyers should request power-on hours, cutting hours, spindle hours, maintenance records, alarm history, crash history, and a test-cut demonstration.

The absence of an ATC should be clearly stated in an inventory listing because the TM2 and TM2P are different configurations.

---

HOW MUCH DOES A USED HAAS TM2 – 2008 COST?

The used value of a 2008 HAAS TM2 depends heavily on spindle condition, hours, machine accuracy, control condition, options, tooling, coolant equipment, and overall maintenance history.

The TM2 generally commands less than a comparable TM2P because it lacks the automatic tool changer and uses a slower 4,000 RPM spindle. Current Haas specifications confirm the distinction between the TM2 and TM2P: the TM2 uses a 4,000 RPM spindle and no standard ATC, while the TM2P adds a 10-pocket ATC, 6,000 RPM spindle, and 400 IPM rapids.

As a practical used-market estimate:

USED HAAS TM2 – 2008 PRICE RANGE	ESTIMATED COST
High Hours / Basic Configuration	$12,000 – $16,000
Functional Used Machine	$16,000 – $20,000
Good Condition / Production Ready	$20,000 – $24,000
Excellent / Well Equipped	$24,000 – $28,000
Very Low Hours / Premium Condition	$28,000+

For a 2008 HAAS TM2 in good working condition, I would estimate approximately $18,000–$24,000 USD.

For your inventory listing, I would recommend a practical asking-price range of $20,000–$24,000 USD for a clean, operational machine.

A low-hour machine with excellent spindle condition, good geometry, probing, 4th-axis capability, coolant equipment, and complete tooling could potentially command $24,000–$28,000+.

A high-hour machine with mechanical wear, control problems, missing accessories, or repair requirements could fall closer to $12,000–$18,000.

Best estimated listing value: $20,000–$24,000 USD.

The most important items to verify before finalizing the price are machine hours, spindle hours, backlash, spindle condition, control condition, included tooling, probing, coolant equipment, and 4th-axis accessories.