OKUMA LB3000 EX-II – 2012
USED OKUMA LB3000 EX-II – 2012
The OKUMA LB3000 EX-II – 2012 is a high-performance CNC horizontal turning center designed for precision production machining. It belongs to Okuma’s SPACE TURN LB EX II family and combines a rigid slant-bed construction with a powerful spindle, large turning capacity, and Okuma’s OSP CNC control.
The LB3000 EX II platform was developed around high rigidity, thermal stability, and productivity. Okuma’s Thermo-Friendly Concept is intended to minimize thermal deformation during extended production, helping maintain dimensional consistency without relying heavily on lengthy warm-up cycles.
Depending on configuration, the LB3000 EX-II can be equipped as a conventional 2-axis turning center or with live tooling and Y-axis capability for milling, drilling, tapping, and other secondary operations. The documented platform specifications include approximately 260 mm of X-axis travel, up to 1,255 mm of Z-axis travel depending on bed configuration, 80 mm spindle bore, and spindle speeds up to 5,000 RPM.
A 2012 machine may also differ from later LB3000 EX-II configurations, so the exact spindle, chuck, control, travel, turret, and options should be verified against the individual machine.
OKUMA LB3000 EX-II – 2012 – MACHINE CAPACITY
| Specification | Details |
|---|---|
| OKUMA LB3000 EX-II – 2012 | |
| Machine Type | CNC Horizontal Turning Center |
| Machine Configuration | 2-Axis / Multi-Tasking Configuration Dependent |
| Swing Over Bed | 22.83 inches / 580 mm |
| Swing Over Carriage | 18.50 inches / 470 mm |
| Maximum Turning Diameter | Up to 16.14 inches / 410 mm |
| Maximum Work Length | Configuration Dependent |
| Bar Capacity | Up to 80 mm / 3.15 in |
| Spindle Bore | 80 mm / 3.15 in |
| Spindle Nose | JIS A2-6 |
| Turret | 12 Station |
| Y-Axis | Configuration Dependent |
| Live Tooling | Configuration Dependent |
| CNC Control | Okuma OSP Series |
| Tailstock | Configuration Dependent |
The LB3000 EX-II is available in several bed and tooling configurations, which is why work length and some capacity specifications can vary considerably between individual machines.
OKUMA LB3000 EX-II – 2012 – AXIS TRAVELS
| Specification | Details |
|---|---|
| OKUMA LB3000 EX-II – 2012 | |
| X-Axis Travel | 260 mm / 10.24 in |
| Z-Axis Travel | 510–1,255 mm / 20.08–49.41 in |
| Y-Axis Travel | Up to 120 mm / 4.72 in on MY configuration |
| X Rapid Traverse | 25 m/min / 984 IPM |
| Z Rapid Traverse | 30 m/min / 1,181 IPM |
| Y Rapid Traverse | 12.5 m/min / 492 IPM |
| Axis Drive | Servo Controlled |
| Positioning | CNC Controlled |
| Linear Interpolation | Supported |
| Circular Interpolation | Supported |
| Multi-Axis Machining | Configuration Dependent |
The MY configuration provides approximately 120 mm of Y-axis travel, allowing off-center milling and drilling operations.
OKUMA LB3000 EX-II – 2012 – SPINDLE SYSTEM
| Specification | Details |
|---|---|
| OKUMA LB3000 EX-II – 2012 | |
| Spindle Type | Horizontal |
| Spindle Motor | Approximately 22/15 kW |
| High-Power Configuration | Up to 30/22 kW |
| Spindle Speed | Up to 5,000 RPM |
| Spindle Bore | 80 mm |
| Spindle Nose | JIS A2-6 |
| Spindle Diameter | 120 mm |
| Spindle Drive | CNC Controlled |
| Spindle Ranges | Automatic 2-Speed / Configuration Dependent |
| C-Axis | Configuration Dependent |
| Rigid Tapping | Supported |
| Spindle Orientation | Supported |
The LB3000 EX-II uses a substantial spindle system intended to provide both turning speed and cutting torque. The technical specification identifies standard spindle motor ratings around 22/15 kW, with higher-power configurations available.
OKUMA LB3000 EX-II – 2012 – TURNING CAPABILITY
| Specification | Details |
|---|---|
| OKUMA LB3000 EX-II – 2012 | |
| Swing Over Bed | 22.83 inches / 580 mm |
| Swing Over Carriage | 18.50 inches / 470 mm |
| Maximum Turning Diameter | 16.14 inches / 410 mm |
| Maximum Work Length | Configuration Dependent |
| Bar Capacity | Up to 3.15 inches / 80 mm |
| OD Turning | Yes |
| ID Turning | Yes |
| Facing | Yes |
| Boring | Yes |
| Threading | Yes |
| Grooving | Yes |
| Parting | Yes |
| Taper Turning | CNC Programmable |
| Contouring | CNC Programmable |
The generous swing and bar capacity make the LB3000 EX-II suitable for medium- and large-sized turned components. Long-bed versions can provide considerably greater machining length for shaft and other extended components.
OKUMA LB3000 EX-II – 2012 – TURRET & TOOLING
| Specification | Details |
|---|---|
| OKUMA LB3000 EX-II – 2012 | |
| Turret Type | Automatic CNC Turret |
| Tool Capacity | 12 Stations |
| OD Tool Size | 25 x 25 mm |
| ID Tool Diameter | 40 mm |
| Live Tooling | Configuration Dependent |
| Live Tool Speed | Up to 6,000 RPM |
| C-Axis | Configuration Dependent |
| Y-Axis | Configuration Dependent |
| Milling | Configuration Dependent |
| Drilling | Supported |
| Tapping | Supported |
| Boring | Supported |
| Tool Offset Management | CNC Controlled |
The V12 turret supports conventional turning tools, while M and MY versions add driven tooling capability. On MY configurations, the combination of live tooling, C-axis, and Y-axis allows the machine to perform milling and off-center drilling operations in the same setup.
OKUMA LB3000 EX-II – 2012 – CNC CONTROL
| Specification | Details |
|---|---|
| OKUMA LB3000 EX-II – 2012 | |
| CNC Control | Okuma OSP Series |
| Programming | G-Code / ISO |
| Control Type | Okuma CNC |
| X/Z Axis Control | CNC |
| Y-Axis Control | Configuration Dependent |
| C-Axis Control | Configuration Dependent |
| Tool Offsets | Supported |
| Work Offsets | Supported |
| Canned Cycles | Supported |
| Threading Cycles | Supported |
| Rigid Tapping | Supported |
| Cutter Compensation | Supported |
| Diagnostics | Integrated |
| Tool Management | CNC Controlled |
The LB3000 EX II was developed around Okuma’s OSP control platform. The OSP-P300L was introduced with the LB3000 EX II model change announced by Okuma in 2012, bringing improved operator interface functionality and the manufacturer’s single-mode operating concept.
OKUMA LB3000 EX-II – 2012 – FEEDRATES
| Specification | Details |
|---|---|
| OKUMA LB3000 EX-II – 2012 | |
| X-Axis Rapid | 984 IPM |
| Z-Axis Rapid | 1,181 IPM |
| Y-Axis Rapid | 492 IPM |
| X Rapid Traverse | 25 m/min |
| Z Rapid Traverse | 30 m/min |
| Y Rapid Traverse | 12.5 m/min |
| Cutting Feedrate | CNC Programmable |
| Feedrate Override | Yes |
| Linear Interpolation | Yes |
| Circular Interpolation | Yes |
| Multi-Axis Feed Control | Configuration Dependent |
The rapid traverse rates are designed to minimize non-cutting positioning time while maintaining the stability required for precision turning and multi-tasking applications.
OKUMA LB3000 EX-II – 2012 – COOLANT & CHIP MANAGEMENT
| Specification | Details |
|---|---|
| OKUMA LB3000 EX-II – 2012 | |
| Flood Coolant | Yes |
| Coolant System | Integrated |
| Chip Conveyor | Configuration Dependent |
| Chip Auger | Configuration Dependent |
| High-Pressure Coolant | Configuration Dependent |
| Through-Tool Coolant | Configuration Dependent |
| Coolant Filtration | Configuration Dependent |
| Automatic Lubrication | Yes |
| Machine Enclosure | Fully Enclosed |
| Parts Catcher | Configuration Dependent |
| Bar Feeder | Configuration Dependent |
The enclosed slant-bed design helps direct chips toward the machine’s chip-management system. Depending on the individual machine, chip conveyors, bar feeders, parts catchers, and other production accessories may be included.
OKUMA LB3000 EX-II – 2012 – TAILSTOCK
| Specification | Details |
|---|---|
| OKUMA LB3000 EX-II – 2012 | |
| Tailstock | Configuration Dependent |
| Tailstock Taper | MT5 |
| Tailstock Travel | Configuration Dependent |
| Tailstock Type | CNC / Manual Configuration Dependent |
| Quill Operation | CNC / Hydraulic Configuration Dependent |
| Long-Part Support | Yes |
| Shaft Machining | Supported |
| Workpiece Support | Configuration Dependent |
A tailstock can provide additional support for long shafts and other workpieces where cutting forces could otherwise cause deflection.
OKUMA LB3000 EX-II – 2012 – POWER REQUIREMENTS
| Specification | Details |
|---|---|
| OKUMA LB3000 EX-II – 2012 | |
| Electrical Service | Three Phase |
| Main Voltage | 200 V Machine Supply |
| Transformer Input | 220/240/380/415/440/480 V Taps |
| Frequency | 50 / 60 Hz |
| Standard Power Requirement | Approximately 27.4 kVA |
| Higher-Power Configuration | Approximately 36.4 kVA |
| Spindle Motor | 22/15 kW Standard Configuration |
| Hydraulic System | Integrated |
| Coolant Pump | Integrated |
| Lubrication Pump | Integrated |
| Industrial Installation | Required |
The technical documentation identifies a 200 V machine supply with transformer taps for several incoming voltages. Actual electrical requirements should always be verified from the individual machine’s electrical nameplate before installation.
OKUMA LB3000 EX-II – 2012 – MACHINE DIMENSIONS
| Specification | Details |
|---|---|
| OKUMA LB3000 EX-II – 2012 | |
| Machine Height | Approximately 88.6–96.7 in |
| Machine Length | Configuration Dependent |
| Machine Width | Configuration Dependent |
| Net Weight | Approximately 10,670–15,180 lb |
| Floor Space | Configuration Dependent |
| Chip Conveyor | Adds to Footprint |
| Bar Feeder | Adds to Footprint |
| Coolant Tank | Adds to Footprint |
| Rigging | Required |
| Installation | Industrial |
The documented specifications show machine weights ranging from approximately 10,670 lb to 15,180 lb, depending on the bed and machine configuration.
OKUMA LB3000 EX-II – 2012 – GENERAL INFORMATION
| Specification | Details |
|---|---|
| OKUMA LB3000 EX-II – 2012 | |
| Manufacturer | Okuma |
| Model | LB3000 EX-II |
| Year | 2012 |
| Machine Category | CNC Turning Center |
| Machine Type | Horizontal CNC Lathe |
| Number of Axes | Configuration Dependent |
| CNC Control | Okuma OSP |
| Swing Over Bed | 580 mm / 22.83 in |
| Swing Over Carriage | 470 mm / 18.50 in |
| Maximum Turning Diameter | Up to 410 mm / 16.14 in |
| X Travel | 260 mm / 10.24 in |
| Z Travel | Up to 1,255 mm / 49.41 in |
| Y Travel | Up to 120 mm / 4.72 in |
| Spindle Bore | 80 mm / 3.15 in |
| Spindle Speed | Up to 5,000 RPM |
| Spindle Motor | Up to 30/22 kW Configuration |
| Turret | 12 Station |
| Live Tooling | Configuration Dependent |
INDUSTRIES THAT USE OKUMA LB3000 EX-II
The OKUMA LB3000 EX-II is suitable for a broad range of precision manufacturing industries, including:
- Automotive
- Aerospace
- Oil & Gas
- Energy
- Medical Manufacturing
- Defense
- Hydraulic Manufacturing
- Pump Manufacturing
- Valve Manufacturing
- Industrial Equipment
- Robotics
- Agricultural Equipment
- Construction Equipment
- General Machine Shops
- Contract Manufacturing
The machine’s combination of turning capacity, rigidity, and optional multi-tasking capabilities makes it useful for both general production and complex precision components.
TYPICAL PARTS OKUMA LB3000 EX-II CAN PRODUCE
The OKUMA LB3000 EX-II can manufacture a wide variety of precision components, including:
- Shafts
- Bushings
- Flanges
- Couplings
- Hydraulic components
- Valve components
- Pump components
- Bearing housings
- Gear components
- Automotive components
- Aerospace fittings
- Industrial fittings
- Rollers
- Adapters
- Threaded components
- Precision housings
MY configurations are particularly useful for parts requiring milled flats, keyways, cross holes, off-center holes, tapped holes, and other secondary features that can be machined using Y-axis and driven tooling capabilities. Okuma specifically identifies keyway, plane, and other milling operations as applications for the Y-axis versions of the LB3000 EX II.
WHY CHOOSE OKUMA LB3000 EX-II
The OKUMA LB3000 EX-II is a strong choice for manufacturers looking for a rigid CNC turning center with excellent accuracy and the ability to handle demanding production workloads.
One of its major advantages is Okuma’s Thermo-Friendly Concept, which is designed to reduce dimensional changes caused by temperature variations during machining. Okuma reports dimensional stability of approximately 5 μm under its specified test conditions, helping the machine maintain accuracy during extended operation.
The platform is also available with multi-tasking capabilities. MY configurations combine Y-axis movement, C-axis control, and live tooling, allowing milling and drilling operations to be performed directly on the turned component.
Its rigid slant-bed construction provides a stable platform for cutting, while the 80 mm spindle bore provides useful bar-working capacity. The 12-station turret also provides adequate tooling flexibility for many production applications.
For manufacturers that value accuracy, rigidity, thermal stability, and process consolidation, the LB3000 EX-II remains a highly capable CNC turning platform.
WHY BUY USED OKUMA LB3000 EX-II – 2012
Buying a used OKUMA LB3000 EX-II – 2012 can give manufacturers access to a high-quality production CNC lathe at a significantly lower acquisition cost than a new machine.
A major benefit is that the LB3000 EX II platform can be configured for both conventional turning and more advanced multi-tasking work. Buyers should therefore verify exactly which version they are purchasing, particularly whether it includes live tooling, Y-axis, C-axis, sub-spindle, bar feeder, parts catcher, and high-pressure coolant.
For a used 2012 machine, buyers should carefully inspect the spindle, spindle bearings, turret, ballscrews, guideways, servo motors, CNC control, hydraulic system, coolant system, lubrication system, chuck, and electrical cabinet.
The spindle should be tested across its full operating range for vibration, bearing noise, temperature, and runout. The turret should be indexed through all positions, and driven-tool stations should be tested where applicable.
The X and Z axes should be checked for backlash, repeatability, positioning accuracy, and abnormal mechanical noise. If the machine has Y-axis capability, the Y-axis should also be tested throughout its travel.
A well-maintained LB3000 EX-II with a healthy spindle, accurate axes, functioning turret, reliable OSP control, complete tooling, and documented maintenance can provide excellent value for production machining.
HOW MUCH DOES A USED OKUMA LB3000 EX-II – 2012 COST?
The price of a used OKUMA LB3000 EX-II – 2012 depends heavily on configuration. A basic 2-axis machine will generally command less than an MY or MW configuration equipped with live tooling, Y-axis, sub-spindle, bar feeder, chip conveyor, and other automation.
Used-market listings for LB3000 EX-II machines show significant variation depending on configuration and condition. A later documented machine with 2,800 hours, 22 kW spindle power, 80 mm bar capacity, 5,000 RPM spindle speed, live tooling, sub-spindle, chip conveyor, and tool setter is listed on a price-on-request basis, illustrating the premium associated with highly equipped configurations.
| USED OKUMA LB3000 EX-II – 2012 CONDITION | ESTIMATED COST |
|---|---|
| As-Is / High Hours | $35,000 – $50,000 |
| Functional / Average Condition | $50,000 – $65,000 |
| Good Production Condition | $65,000 – $80,000 |
| Excellent / Well Equipped | $80,000 – $100,000 |
| Low Hours / MY/MW Configuration | $100,000+ |
For a 2012 OKUMA LB3000 EX-II in good working condition, a reasonable used-market estimate is approximately $55,000–$85,000 USD.
A machine equipped with Y-axis, live tooling, C-axis, sub-spindle, bar feeder, chip conveyor, tool setter, high-pressure coolant, and complete tooling can command a significant premium over a basic 2-axis configuration.
Best estimated listing value: $65,000–$85,000 USD.
Related Products
-
OKUMA - MU-10000H
VIEW MACHINE -
OKUMA - GENOS L400II-E
VIEW MACHINE -
OKUMA - MA-12500H
VIEW MACHINE -
OKUMA - MULTUS B300II
VIEW MACHINE