USED HAAS SL30T – 2003
The HAAS SL30T – 2003 is a heavy-duty CNC turning center designed for production machining of medium- to large-sized cylindrical components. With a 10-inch chuck, approximately 3-inch bar capacity, 30-inch swing, 17-inch maximum turning diameter, and up to 34 inches of turning length on certain configurations, the SL30T provides substantial machining capacity for its class.
The machine uses a Haas CNC control and a 12-station automatic turret, allowing manufacturers to perform turning, facing, boring, threading, grooving, drilling, and other conventional CNC lathe operations efficiently. A 30 HP spindle and maximum spindle speed of approximately 3,400 RPM provide a useful combination of power and speed for machining steel, aluminum, stainless steel, cast iron, and other industrial materials.
The 2003 SL30T was available with features such as a programmable hydraulic tailstock, tool presetter, automatic door, chip auger or conveyor, parts catcher, and other production-oriented equipment depending on the individual machine.
HAAS SL30T – 2003 – MACHINE CAPACITY
| Specification | Details |
|---|---|
| HAAS SL30T – 2003 | |
| Machine Type | CNC Turning Center |
| Number of Axes | 2 |
| Chuck Size | 10 inches |
| Maximum Swing | 30 inches |
| Maximum Turning Diameter | Up to 17 inches |
| Maximum Turning Length | Up to 34 inches |
| Bar Capacity | 3 inches |
| Spindle Bore | 3.5 inches |
| Spindle Nose | A2-6 |
| Turret | 12 Station |
| Tailstock | Yes |
| CNC Control | Haas CNC |
| Live Tooling | Configuration Dependent |
| Sub-Spindle | No |
| Y-Axis | No |
The SL30T’s large swing and 3-inch bar capacity make it suitable for considerably larger workpieces than compact CNC lathes. Exact cutting capacity can vary with the particular machine configuration and workholding arrangement.
HAAS SL30T – 2003 – AXIS TRAVELS
| Specification | Details |
|---|---|
| HAAS SL30T – 2003 | |
| X-Axis Travel | Approximately 9.4–11.3 inches |
| Z-Axis Travel | Approximately 32.5–34 inches |
| X-Axis Rapid Traverse | Approximately 710 IPM |
| Z-Axis Rapid Traverse | Approximately 710–945 IPM |
| Axis Drive | Servo Controlled |
| Axis Positioning | CNC Controlled |
| X/Z Interpolation | Supported |
| Automatic Positioning | Standard |
| Ballscrews | Precision CNC Configuration |
Published specifications for individual 2003 machines differ slightly, particularly regarding X and Z travel, so buyers should verify the original machine specification sheet before purchase.
HAAS SL30T – 2003 – SPINDLE SYSTEM
| Specification | Details |
|---|---|
| HAAS SL30T – 2003 | |
| Spindle Motor | Up to 30 HP |
| Maximum Spindle Speed | 3,400 RPM |
| Spindle Bore | 3.5 inches |
| Spindle Nose | A2-6 |
| Chuck | 10-inch Hydraulic Chuck |
| Chuck Type | 3-Jaw Hydraulic |
| Maximum Bar Capacity | 3 inches |
| Maximum Torque | Approximately 300 ft-lb |
| Spindle Drive | CNC Controlled |
| Spindle Orientation | CNC Controlled |
| Gearbox | Configuration Dependent |
The 30 HP spindle gives the SL30T the power required for aggressive material removal. The A2-6 spindle nose and 3.5-inch bore are particularly useful for production work involving larger diameter bar stock.
HAAS SL30T – 2003 – TURNING CAPABILITY
| Specification | Details |
|---|---|
| HAAS SL30T – 2003 | |
| Maximum Swing | 30 inches |
| Swing Over Cross Slide | Approximately 14.5 inches |
| Maximum Turning Diameter | Up to 17 inches |
| Maximum Turning Length | Up to 34 inches |
| Distance Between Centers | Up to 39 inches |
| Maximum Bar Capacity | 3 inches |
| OD Turning | Yes |
| ID Turning | Yes |
| Facing | Yes |
| Boring | Yes |
| Threading | Yes |
| Grooving | Yes |
| Parting | Yes |
| Taper Turning | CNC Programmable |
| Contouring | CNC Programmable |
The large work envelope allows the SL30T to handle shafts, bushings, flanges, fittings, housings, adapters, and other industrial components that may exceed the capacity of smaller CNC turning centers.
HAAS SL30T – 2003 – TURRET & TOOLING
| Specification | Details |
|---|---|
| HAAS SL30T – 2003 | |
| Turret Type | Automatic CNC Turret |
| Turret Capacity | 12 Stations |
| Tool Mounting | Configuration Dependent |
| Tool Presetter | Configuration Dependent |
| OD Turning Tools | Supported |
| ID Boring Tools | Supported |
| Grooving Tools | Supported |
| Threading Tools | Supported |
| Parting Tools | Supported |
| Drill Holders | Supported |
| Live Tooling | Configuration Dependent |
The 12-station turret provides sufficient tool capacity for many production jobs without requiring frequent manual tool changes. Some used SL30T machines are equipped with tool presetters and complete tooling packages, which can add considerable value to a used machine.
HAAS SL30T – 2003 – CNC CONTROL
| Specification | Details |
|---|---|
| HAAS SL30T – 2003 | |
| CNC Control | Haas CNC |
| Programming | G-Code / ISO |
| X/Z Axis Control | CNC |
| Tool Offsets | Supported |
| Work Offsets | Supported |
| Canned Cycles | Supported |
| Threading Cycles | Supported |
| Tool Compensation | Supported |
| Feedrate Override | Supported |
| Spindle Override | Supported |
| Diagnostics | Integrated |
| Program Storage | Configuration Dependent |
| Communication | Configuration Dependent |
The Haas control architecture was designed to provide straightforward operation for CNC turning applications. However, on a machine manufactured in 2003, the exact control hardware, memory capacity, communication options, and interface features should be verified because machines can have different original or upgraded configurations.
HAAS SL30T – 2003 – FEEDRATES
| Specification | Details |
|---|---|
| HAAS SL30T – 2003 | |
| X-Axis Rapid | Approximately 710 IPM |
| Z-Axis Rapid | Approximately 710 IPM |
| Cutting Feedrate | CNC Programmable |
| Feedrate Override | Yes |
| Rapid Traverse | CNC Controlled |
| Linear Interpolation | Yes |
| Circular Interpolation | Yes |
| Threading Feedrate | CNC Controlled |
| Automatic Feed Control | CNC Controlled |
Rapid positioning rates of approximately 710 IPM are reported for several 2003 SL30T configurations. Some machine listings report higher Z-axis rapid rates, so the individual machine should be checked before publishing exact specifications for a specific inventory listing.
HAAS SL30T – 2003 – COOLANT & CHIP MANAGEMENT
| Specification | Details |
|---|---|
| HAAS SL30T – 2003 | |
| Flood Coolant | Yes |
| Coolant System | Integrated |
| Chip Removal | Chip Auger / Conveyor |
| Chip Auger | Configuration Dependent |
| Chip Conveyor | Configuration Dependent |
| High-Pressure Coolant | Configuration Dependent |
| Automatic Lubrication | Yes |
| Coolant Delivery | Tool Area |
| Machine Enclosure | Fully Enclosed |
| Parts Catcher | Configuration Dependent |
| Auto Jet Blast | Configuration Dependent |
Chip management is particularly important when machining large quantities of steel or other materials that produce substantial chip volume. Many used SL30T machines are equipped with chip augers or conveyors to automate chip removal.
HAAS SL30T – 2003 – TAILSTOCK
| Specification | Details |
|---|---|
| HAAS SL30T – 2003 | |
| Tailstock | Yes |
| Tailstock Type | Hydraulic / Programmable |
| Tailstock Taper | MT-4 |
| Quill Diameter | Approximately 2.6 inches |
| Quill Travel | Approximately 3.1 inches |
| Body Travel | Approximately 33.5 inches |
| CNC Positioning | Supported |
| Hydraulic Operation | Configuration Dependent |
The tailstock is useful for supporting long shafts and other workpieces where additional support is required during turning. Programmable hydraulic tailstock configurations can improve repeatability and reduce manual setup requirements.
HAAS SL30T – 2003 – POWER REQUIREMENTS
| Specification | Details |
|---|---|
| HAAS SL30T – 2003 | |
| Electrical Service | Three Phase |
| Typical Voltage | 220V or 480V Configuration Dependent |
| Frequency | 60 Hz |
| Spindle Motor | Up to 30 HP |
| Power Source | AC |
| Compressed Air | Approximately 100 PSI |
| Air Consumption | Approximately 4 SCFM |
| Hydraulic System | Integrated |
| Coolant Pump | Integrated |
| Automatic Lubrication | Yes |
Electrical requirements can vary depending on the original configuration and installed drive package. Some 2003 machines are listed with 220V three-phase power, while others are equipped for higher-voltage service.
HAAS SL30T – 2003 – MACHINE DIMENSIONS
| Specification | Details |
|---|---|
| HAAS SL30T – 2003 | |
| Approximate Length | 161–171 inches |
| Approximate Width | 77–90 inches |
| Approximate Height | 74–98 inches |
| Approximate Weight | 14,300–16,000 lbs |
| Machine Type | Large CNC Turning Center |
| Chip Conveyor | Adds to Overall Footprint |
| Bar Feeder | Adds to Overall Footprint |
| Rigging | Required |
| Installation | Industrial |
Published dimensions and weight vary between individual 2003 SL30T machines and configurations. A machine equipped with a chip conveyor, bar feeder, or other accessories will require additional floor space.
HAAS SL30T – 2003 – GENERAL INFORMATION
| Specification | Details |
|---|---|
| HAAS SL30T – 2003 | |
| Manufacturer | Haas |
| Model | SL30T |
| Year | 2003 |
| Machine Category | CNC Lathe / Turning Center |
| Number of Axes | 2 |
| CNC Control | Haas CNC |
| Chuck Size | 10 inches |
| Spindle Speed | 3,400 RPM |
| Spindle Power | Up to 30 HP |
| Bar Capacity | 3 inches |
| Spindle Bore | 3.5 inches |
| Turret | 12 Station |
| Tailstock | Yes |
| Machine Construction | Enclosed Slant-Bed CNC Lathe |
INDUSTRIES THAT USE HAAS SL30T
The HAAS SL30T can be used across a wide range of manufacturing industries, including:
- Automotive
- Aerospace
- Oil & Gas
- Industrial Equipment
- Hydraulic Manufacturing
- Pump Manufacturing
- Valve Manufacturing
- Heavy Equipment
- Agricultural Equipment
- Defense
- General Machine Shops
- Job Shops
- Contract Manufacturing
- Fabrication and Repair
Its combination of large turning capacity, substantial spindle power, and automatic tooling makes it particularly useful for shops machining medium- and large-diameter components.
TYPICAL PARTS HAAS SL30T CAN PRODUCE
The HAAS SL30T can manufacture a broad range of cylindrical and rotational components, including:
- Shafts
- Bushings
- Flanges
- Hydraulic cylinders
- Valve components
- Pump components
- Housings
- Adapters
- Couplings
- Rollers
- Spacers
- Threaded components
- Bearing components
- Industrial fittings
- Automotive components
- Oil & gas components
With a 3-inch bar capacity and large turning envelope, the machine is well suited to components that require substantial material removal and longer machining lengths.
WHY CHOOSE HAAS SL30T
The HAAS SL30T remains attractive in the used CNC market because it combines relatively straightforward CNC operation with substantial turning capacity. Its 10-inch chuck, 3-inch bar capacity, 30 HP spindle configuration, 12-station turret, and large work envelope make it considerably more capable than many smaller CNC lathes.
The machine is especially useful for manufacturers that need to turn larger workpieces but do not necessarily require a modern multi-axis turning center. Standard operations such as OD and ID turning, facing, boring, threading, grooving, and parting can be programmed directly through the CNC control.
Another advantage is the availability of replacement tooling and service knowledge for Haas equipment. For a machine shop already operating Haas equipment, adding an older SL30T can also simplify operator training and workflow.
A well-maintained SL30T can therefore provide a cost-effective combination of spindle power, workholding capacity, turning envelope, and production capability.
WHY BUY USED HAAS SL30T – 2003
Buying a used HAAS SL30T – 2003 can be an economical way to add a full-size CNC turning center without the capital expense associated with purchasing a new machine.
The age of the machine makes inspection especially important. Buyers should evaluate the spindle, chuck, hydraulic system, turret, ballscrews, linear guides, servo motors, CNC control, electrical cabinet, tailstock, coolant system, lubrication system, and chip-removal equipment.
The spindle should be checked for abnormal bearing noise, vibration, runout, temperature, and taper condition. Axis performance should be evaluated for backlash, repeatability, positioning accuracy, and unusual noise throughout the complete travel range.
The turret should be tested at every station to ensure reliable indexing and proper tool clamping. If the machine includes a hydraulic tailstock, parts catcher, tool presetter, chip conveyor, bar feeder interface, or other options, each accessory should also be tested.
A machine with documented maintenance, good spindle condition, functioning CNC control, complete tooling, and clean overall mechanical condition can offer considerably better value than a low-priced machine requiring extensive repairs.
HOW MUCH DOES A USED HAAS SL30T – 2003 COST?
Used 2003 HAAS SL30T machines have recently been advertised at substantially different prices depending on condition, hours, tooling, accessories, and configuration. Examples include asking prices around $21,000 and $26,500, while broader historical SL-30 asking-price data shows machines listed in approximately the $17,500–$37,500 range. These are asking prices rather than confirmed transaction prices.
| USED HAAS SL30T – 2003 CONDITION | ESTIMATED COST |
|---|---|
| As-Is / High Hours | $15,000 – $20,000 |
| Functional / Average Condition | $20,000 – $27,500 |
| Good Condition | $27,500 – $35,000 |
| Excellent Condition / Well Equipped | $35,000 – $42,000 |
| Low Hours / Exceptional Configuration | $42,000+ |
For a 2003 HAAS SL30T in good working condition, a reasonable current market estimate is approximately $22,000–$35,000 USD.
A clean machine with a good spindle, functioning Haas control, 10-inch chuck, 12-station turret, tailstock, chip conveyor or auger, tool presetter, parts catcher, and useful tooling package can command a premium over a basic machine.
Best estimated listing value: $27,500–$35,000 USD.
Related Products
-
HAAS - TL2
VIEW MACHINE -
HAAS - VF3SSAPC
VIEW MACHINE -
HAAS - ST20SS
VIEW MACHINE -
HAAS - VF2B
VIEW MACHINE